ETRUSIA
  1. Home
  2. Integrations
  3. TigerStop

Integration · TigerStop saw positioners

The cut list goes to the TigerStop. Nobody keys a length.

At a window plant's vinyl saw, the cut list already lives in the order. Extrusia's saw screen shows the operator which piece is next and sends its length to the TigerStop over the serial cable the stop already has. The stop moves, the operator cuts, and the piece is recorded against the window it belongs to.

How the TigerStop connection works

The stop moves by itself

Opening a batch sends the first piece's length. After each cut, the next length goes to the stop only if it is different, so a run of identical pieces moves the stop once. The operator presses the pedal to cut, without keying a length.

A cut is only recorded at the right length

The pedal records a cut only while the stop is at that piece's length. If the stop was never told the length, the press sends it instead and records nothing, so no cut is ever logged against a length the saw did not stop at.

Pieces in the saw's natural order

Each profile is cut longest first, with identical lengths back to back. The order changes how the operator walks the batch, not which bars it uses: every piece still says which bar it comes from, and which leftovers to keep.

Lengths to four decimals

Cut lengths come from the window's own bill of material and print to four decimal places on the screen and the cut sheet, so 30.5 and 30.5625 never look like the same cut.

More than one person at one saw

A window type cut by someone else, such as casements or patio doors, can be cut as its own list within the same batch, so one person's pieces never hold up the rest of the order.

Nothing lost on a reload

Which piece is next is kept by Extrusia, not by the saw PC. A browser that closes, or a PC that restarts, opens on the same piece, and every cut carries a time, so the plant can see how far into a batch the saw is.

What sits between the screen and the stop

The TigerStop is a box on a serial port, and Extrusia is in the cloud. The bridge between them is the small Extrusia agent on the saw PC, which runs as a Windows service on Windows 7 and later, including the rugged laptops common at saws. The screen sends a length to the agent on the same PC, and the agent writes it to the stop's COM port.

  • The stop's own command language. A move is sent the way TigerStop controllers expect it, proven against a working saw on a V5 controller. The earlier controller generation's dialect is a setting.
  • Settings in one place. The saw's port and settings are kept on the device in your workspace, where an administrator can see them, rather than buried on the saw PC.
  • The port is let go when the saw is idle. A serial port has one owner. After a short quiet spell the agent releases it, so another program on the same PC can still reach the saw, for example while an old system and Extrusia run side by side.
  • A failed send never stops the saw. If the stop cannot be reached, the screen says so in plain words and the operator can set the stop by hand and keep cutting.
  • A practice mode. A saw being set up can write the exact bytes it would send to a file instead of the port, so the whole chain is checked before the stop moves.

Note: TigerStop is a trademark of its owner. Extrusia is not affiliated with or endorsed by TigerStop; the name describes the equipment Extrusia exchanges data with.

TigerStop integration — common questions

Does the TigerStop need a network connection?

No. The stop stays on its serial cable to the saw PC, as it is today. Only the PC talks to Extrusia.

Do we have to replace our saw PC?

Usually not. The Extrusia agent runs on Windows 7 and later, including older Toughbooks at the saw.

Can the operator still cut if the connection fails?

Yes. The screen keeps working, says the stop could not be reached, and lets the operator set the length by hand and carry on.

Does Extrusia change which bars a batch uses?

No. The cutting order is arranged for the operator, longest first within each profile, but every piece stays on the bar the plan put it on.

See it on your own products

The best demo is your own catalog.

Send us what you make and what you run today. We'll show you Extrusia quoting your own windows, at your own prices, checked against what your current system says.